+44 (0)1543 277003

Proximity Sensors

Detection & Control – in Action!
Designed and manufactured by SYNATEL – a selection of proximity sensors, both inductive and capacitive, in a variety of enclosures ranging from 12mm diameter dc type upto 40mm DIN standard limit switch style. ATEX and IECEx approved sensors for dust and gas hazard areas are available, which can also be used in non-approved applications.
Accessory items are also available, to allow easy fitting of sensors to shafts etc., without the need for additional guarding. (See Whirligig).
SYNATEL manufacture the UK’s largest range of industrial electronic sensing, counting and control equipment for industry, including ATEX and IECEx sensors, ATEX and IECEx components and switches, ATEX and IECEx enclosures.
(If you have a special requirement, use our contact us page with details).

30mm capacitance sensors

30mm Capacitive/Capacitance Proximity Sensor
ATEX EN 60079/IECEx 60079
(Dust zone20/Gas zone0)

An innovative range of 30mm capacitive proximity sensors, designed & manufactured by SYNATEL available as 5 wire Relay output or 2 wire FET output, multivoltage units. Ideal for level detection in small hoppers, etc. ATEX EN60079 & IECEx IEC 60079 gas & dust hazard area use approvals.

30mm Inductive sensors switches

30mm Inductive Proximity Sensor
ATEX EN 60079/IECEx 60079
(Dust zone20/Gas zone0)

A range of 30mm inductive proximity sensors, designed & manufactured by SYNATEL available as 4 wire DC or 2 wire multivoltage units. Ideal for target detection on rotating/reciprocating machinery.
ATEX EN60079 & IECeX IEC 60079 gas & dust hazard area use approvals.

18mm Inductive proximity sensors

18mm Inductive Proximity Sensor
ATEX EN 60079/IECEx 60079
(Dust zone21/Gas zone1)

SYNATEL design & manufacture a range of 18mm inductive proximity sensors, available as 4 wire DC or 2 wire FET multivoltage units. Ideal for target detection on rotating/reciprocating machinery.
ATEX EN60079 & IECeX IEC 60079 gas & dust hazard area use approvals.

ID1LS 12mm Proximity sensor

12mm DC Inductive Proximity Sensor

A 12mm dia. dc inductive proximity sensor supplied by SYNATEL, ideal for general use, such as target detection on rotating/reciprocating machinery. Non-approved.

UD1DR - ID/E1DOv DIN Proximity Sensor

DIN Standard Limit Switch Style Inductive Proximity Sensor

SYNATEL moulded DIN limit switch style housing proximity sensors. Non-approved. Ideal for general use, such as replacing existing limit switches or target detection on rotating/reciprocating machinery.

WHIRLIGIG Proximity Sensor Attachment Accessory EN 80079 (Dust zone20/Gas zone0) WG1

WHIRLIGIG WG1 Proximity Sensor/Speed Monitor Attachment Accessory
ATEX EN 80079 (Dust zone20/Gas zone0)

A low cost, fully contained speed monitoring attachment, allowing easy fitting of all SYNATEL 18/30mm diameter & DIN standard limit switch style inductive proximity sensors/speed monitors. ATEX mechanical approval.

WGHD Heavy Duty Whirligig

WGHD Heavy Duty Whirligig

WGHD Heavy Duty Whirligig: Heavy duty , all stainless steel construction, fully contained speed monitoring attachment, ideal for mine or quarry use. Allows easy fitting of all Synatel 12/18/30mm diameter inductive proximity sensors/speed monitors. Simple M16 fixing. Targets are fully enclosed and require no further guarding.

Speedmaster + Pulse Pilot

SPEEDMASTER SSM1 Sensor Calibration Checker/programmer
(Audit)

The SpeedMaster from SYNATEL is a test instrument designed to check the function and calibration of all types of SYNATEL speed monitors.
SPEEDMASTER SSM1 + PULSE PILOT PP1 – Speed/Switch point Calibration Checker (Ideal for Calibration/Auditing).

Part of the DonElec Group